Rooflight upstands & kerbs in Stockton-on-Tees: what is involved?
For Stockton-on-Tees homes and buildings we offer rooflight upstands & kerbs: insulated kerbs built and waterproofed to suit your rooflight. We measure first, specify to the opening and confirm any planning or building-control points before quoting.
Older flat-roofed extensions in the North East are often due a new roof covering — the right time to upgrade the rooflight too. In Stockton-on-Tees, as anywhere, rooflight upstands & kerbs are the usual choice for new flat-roof openings and rooflight replacements.
Stockton-on-Tees sits about 3 km from Billingham and 4 km from Thornaby-on-Tees, and we cover the whole TS19 postcode district and the roads in between.
Options we can specify in Stockton-on-Tees
- Upstands to suit single-ply, felt, GRP or liquid roofs
- Proprietary insulated kerbs
- Upstand repairs and rebuilds
- Raised upstands for deep green or ballasted roofs
- Timber upstands with insulation
- Fixings and falls agreed with the rooflight maker
- Matched to your roof covering
What to check first
- Membrane compatibility with the rooflight's sealants
- Minimum upstand height is set by the rooflight manufacturer — commonly 150 mm above the finished roof
Planning, building control and Stockton-on-Tees
Most rooflights on English houses do not need planning permission, provided they keep within 150 mm of the roof surface and below the ridge line. Listed buildings need listed building consent, flats have no householder permitted development rights, and an Article 4 direction can remove the rights in some conservation areas.
Building Regulations Approved Document L sets a limiting U-value of 2.2 W/m²K for new or replacement rooflights in existing homes, measured in the horizontal plane; roof windows need 1.4 W/m²K or a Band B energy rating. The Future Homes and Buildings Standards, published in March 2026, apply from 24 March 2027 and keep the 2.2 W/m²K limit for rooflights.
Our planning guide covers each nation in more detail.
What do rooflight upstands & kerbs cost in Stockton-on-Tees?
These are typical supply-and-fit ranges. For an address in Stockton-on-Tees, scaffold, a hoist for heavy glass, or a new structural opening can move the figure, which is why we survey first.
| Option | Guide price inc VAT | Ex VAT |
|---|---|---|
| Large or raised upstand | £715 – £1,195 | £595 – £995 |
| Standard insulated upstand Typical | £475 – £715 | £395 – £595 |
| Small upstand on new roof | £355 – £475 | £295 – £395 |
What happens next
- Tell us what you have. Send the TS19 postcode, a rough size and a couple of photos.
- Measure and check. A surveyor visits Stockton-on-Tees, measures and checks structure and access.
- Fixed quote. Product, work and price in writing — nothing is ordered until you agree.
- Fit and make good. We fit, seal, test and finish the reveal, then hand over the paperwork.
Rooflight upstands & kerbs near Stockton-on-Tees
Other services in Stockton-on-Tees
Common questions
What roof coverings do you work with?
Single-ply, EPDM, felt, GRP and liquid-applied systems — or we coordinate with your roofer.
Can an old upstand be reused?
If it is sound, square, insulated and the right size. Often it is cheaper to rebuild than adapt.
Does every rooflight need an upstand?
Flat and dome rooflights do. Pitched roof windows use flashing kits instead.
Can you work alongside my builder in Stockton-on-Tees?
Yes. On new extensions we fit once the opening and upstand are ready and coordinate dates with your builder.
Do I need to be at home for the survey in Stockton-on-Tees?
Yes — someone needs to let us into the room below and, where possible, show us how the roof is reached.
